T Onneau Cover Soft Roll Up For 2007-2013 T Oyota Tundra Base 66.7 5.5FT Bed--A86260-2570794385

Stop letting rain, UV, and prying eyes ruin your haul. The Mankee Soft Roll-Up Tonneau Cover is purpose-engineered for the 2007-2013 Toyota Tundra 5.5 ft short bed, delivering commercial-grade cargo protection with a clean, low-profile look that won't compromise your truck's utility or resale value. Compatibility This tonneau cover is designed exclusively for second-generation Toyota Tundra trucks produced in model years 2007, 2008, 2009, 2010, 2011, 2012, and 2013. It fits only the 5.5 ft short bed configuration, which measures approximately 66.7 inches in interior bed length from the bulkhead to the inside face of the tailgate. This cover is engineered for the Base trim and fits standard factory bed rails without modification. It is NOT compatible with Tundra trucks equipped with the 6.5 ft or 8.1 ft bed. Before ordering, measure your bed length from the inside of the cab bulkhead to the inside of the tailgate to confirm you have the 66.7-inch (5.5 ft) short bed. When in doubt, cross-reference your VIN or door-jamb sticker for bed size confirmation. Key Benefits • Weather-Sealed Cargo Protection — Heavy-duty triple-layer vinyl laminate forms a watertight barrier against rain, road spray, UV rays, and road dust, keeping tools, camping gear, groceries, and equipment dry on every trip, every season. • No-Drill, Clamp-On Installation — Aluminum side rails attach directly to your Tundra's existing bed rail using a clamp-on system that requires zero drilling, zero welding, and zero permanent modification, preserving factory fit and finish. • Instant Full Bed Access — The roll-up design lets you unroll or re-secure the cover in seconds without tools, giving you full, unobstructed access to your entire bed whenever you need it. • Aerodynamic Low Profile — The slim, flush-mount design reduces wind drag compared to hard-shell alternatives, helping maintain fuel efficiency on highway runs. • Secure Locking System — Hook-and-loop fastener straps and integrated buckle hardware hold the cover taut in rolled or flat positions, preventing flapping at highway speeds. • Matte Black Finish — The understated matte black surface complements the Tundra's factory exterior styling without the glare or fingerprint issues common to gloss finishes. Technical Specifications • Fitment: 2007-2013 Toyota Tundra Base, 5.5 ft short bed only • Interior Bed Length Covered: 66.7 inches (approximately 5.5 ft) • Cover Material: Triple-layer vinyl laminate with tear-resistant UV-inhibiting topcoat • Frame Material: Lightweight aluminum alloy cross-bows and side rails • Mounting System: No-drill clamp-on hardware, fits standard OEM bed rails • Finish: Matte black • Operating Temp Range: -40°F to 160°F (suitable for all US climate zones) • Fastening: Hook-and-loop straps with buckle retention system Materials & Build Quality The Mankee tonneau cover is constructed from a premium triple-layer vinyl laminate engineered to withstand the harsh demands of daily truck use across all US climate zones. The outer layer incorporates a UV-inhibiting coating that resists fading, cracking, and brittleness even after prolonged exposure to intense sunlight in Southern and Southwestern states. The middle layer adds structural rigidity and tear resistance, while the inner liner is soft enough to protect the bed's paint and finish from scratching during installation and daily use. The aluminum alloy cross-bow framework distributes load evenly across the cover's surface, preventing sagging under light snow accumulation or pooling rainwater. The aluminum side rails are mill-finished and coated to resist corrosion from road salt, a critical feature for truck owners in Northern states and the Rust Belt. Integrated foam seals run along all four edges of the cover to create a weather-tight perimeter seal that keeps water and debris out even in heavy downpours. Every component is pre-assembled at the factory for a straightforward out-of-box experience. Installation Guide Installing the Mankee Soft Roll-Up Tonneau Cover requires no special tools and takes approximately 20-30 minutes for most owners. Step 1: Clean the top surface of both bed side rails with a damp cloth and allow to dry completely to ensure the clamps grip without slipping. Step 2: Lay the tonneau cover panel flat across the bed with the hinge end aligned flush against the cab bulkhead. Step 3: Slide the pre-attached aluminum side rail brackets over the top of each bed rail, positioning them evenly from front to rear. Step 4: Hand-tighten the clamp bolts under each rail using the included hardware — no drilling required. Step 5: Working from the cab end outward, press the hook-and-loop foam seals along the front and side edges to confirm contact with the bed rail surface. Step 6: Extend the cover toward the tailgate, attach the rear buckle straps to the tailgate, and check tension across the full panel. Step 7: Roll up the cover from the tailgate end, secure with the included buckle straps in the rolled position, and verify the cab-end seal is airtight. If you encounter fitment issues, re-verify your bed length before contacting support. What's in the Box • 1x Mankee triple-layer vinyl roll-up tonneau cover panel • 2x Aluminum alloy side rails with pre-installed clamp hardware • 3x Aluminum alloy cross-bow supports • 1x Set of hook-and-loop retention straps with buckle hardware • 1x Foam perimeter weather seal strip set • 1x Installation hardware bag (clamp bolts, nuts, and washers) • 1x Illustrated installation instruction sheet Why Shop With Us We specialize in fitment-specific truck accessories for working pickups and commercial vehicles across the US. Every product in our catalog is vetted for accurate year, make, model, and bed-size compatibility before it goes live — because we know a wrong-fitment return costs you time you don't have. We offer fast domestic shipping, responsive US-based customer support, and a hassle-free return process if anything doesn't meet your expectations. Our product listings include real specifications, honest compatibility warnings, and detailed installation guidance so you can order with confidence and install without frustration. Upgrade your 2007-2013 Toyota Tundra with the Mankee Soft Roll-Up Tonneau Cover today. Add it to your cart now and protect your cargo on every job site run, road trip, and weekend haul.