Dreifach Faltbare Ladeflächenabdeckung, Kompatibel Mit Toyota Tundra 2014– (NICHT PASSEND Für Trail Special Edition Mit Aufbewahrungsboxen), Fleetside 5, 5’ (67") Kurze Ladefläche

Keep your cargo locked, protected, and out of sight without sacrificing a drop of your Tundra's utility. The JiaYao Tri-Fold Tonneau Cover is built from the ground up for 2014-and-newer Toyota Tundra owners running the 5.5-foot Fleetside short bed — delivering a factory-flush, weather-tight seal and one-handed operation every single day. Compatibility is the first question every truck owner should ask, and the answer here is precise. This cover is engineered exclusively for the 2014+ Toyota Tundra equipped with the 5.5-foot (67-inch) Fleetside short bed. That includes CrewMax and Double Cab configurations that left the factory with this bed length. Before ordering, confirm your bed measurement by running a tape measure along the inside of the bulkhead straight to the inside of the tailgate — you need to land at 67 inches. One critical exception: if your Tundra is a Trail Special Edition with the factory-integrated in-bed storage boxes, this cover will NOT fit. The panel mounting rails conflict with those built-in compartments, and forcing the fit will result in gaps, leaks, and potential damage to your bedrail. When in doubt, verify your trim level and bed specs before placing your order. • Weather-Sealed Defense — A full-perimeter rubber weatherstrip gasket runs the entire circumference of the cover, blocking out rain, road spray, dust, UV radiation, and seasonal debris so your tools, luggage, and gear arrive exactly as you loaded them. • Three-Panel Tri-Fold Access — Three equal-width panels fold accordion-style toward the cab, giving you 100% unrestricted bed access in under five seconds — no removal, no storage hassle, and no compromising on payload when you need the full box. • Integrated Locking Latch — A built-in latch with a dedicated key cylinder secures the cover at the tailgate end, adding a meaningful theft-deterrent layer for job-site tools, sporting equipment, or everyday cargo. • No-Drill Clamp-On Mounting — The clamping rail system attaches directly to your existing bedrails without any drilling, cutting, or permanent modification, keeping your truck's resale value intact and making future removal straightforward. • Low-Profile Flush Design — The slim, aerodynamic profile sits flush with the top of your bed rails, maintaining the clean factory silhouette of the Tundra and reducing wind drag at highway speeds compared to raised or bulky alternatives. • UV-Resistant Matte Black Finish — The top panel surface carries a UV-stable matte black coating that resists fading, chalking, and surface degradation through prolonged sun exposure — critical for owners in Southern, Southwestern, or high-altitude markets. • Fitment: 2014+ Toyota Tundra, 5.5 ft / 67" Fleetside short bed only • Fold Style: Tri-fold, three equal panels, forward-folding toward cab • Mounting: Clamp-on rail system, zero drilling required • Seal: Full-perimeter rubber weatherstrip gasket • Surface Finish: Matte black, UV-resistant top coat • Latch: Integrated key-cylinder locking latch at tailgate • Profile: Low-profile flush-mount design • Excludes: Tundra Trail Special Edition with factory in-bed storage boxes The panels are constructed with a rigid internal framework wrapped in a UV-stabilized matte black surface layer. This dual-layer build strategy gives each panel the structural rigidity to resist flex under load or wind pressure at highway speeds, while the outer coating shrugs off the relentless punishment of direct sun exposure. The rubber weatherstrip gasket is not a simple foam strip — it is a formed, full-perimeter seal designed to compress evenly against the bedrail surface and tailgate cap, creating a consistent moisture barrier even when water pools on top of the panels during heavy rain. The clamp hardware is corrosion-resistant, making this cover a solid long-term choice for owners in coastal climates or regions where road salt is a seasonal reality. Every component in the mounting assembly is matched to the specific rail geometry of the 2014+ Tundra bed, eliminating the shimming and gap-filling workarounds that plague universal-fit covers. Installing this tonneau cover is a genuine one-person job that requires no special tools and takes most owners between 20 and 40 minutes from unboxing to first fold. Start by laying the unfolded cover across your Tundra's bed to confirm panel orientation — the latch end faces the tailgate and the hinge end faces the cab. Slide the mounting rails into the channel along each bedrail, positioning them so the front rail sits flush against the cab bulkhead. Tighten the clamp bolts finger-tight first, then use a socket wrench or ratchet to snug them down evenly — alternate side to side so the rail seats squarely. Do not overtighten; the clamps need firm contact, not crushing force. Once rails are secure, attach the cover's hinge brackets to the front rail and fold the panels out toward the tailgate. Connect the rear latch mechanism, close the tailgate, and test the lock cylinder with both keys provided. Finally, run your fingers along the full perimeter of the weatherstrip to confirm even contact with the bedrail surface and tailgate cap. Make minor rail adjustments if you detect any gap. Your cover is ready for use on the first drive. • JiaYao Tri-Fold Tonneau Cover (three-panel assembly, pre-hinged) • Left and right mounting rail clamps (hardware included) • Full-perimeter rubber weatherstrip gasket (pre-installed) • Integrated locking latch with key cylinder • Two matching keys • Installation hardware bag (clamp bolts, washers) • Instruction sheet At Expedite Parts, we stock fitment-specific truck accessories because we know a wrong-fit return wastes your time and your weekend. Every product listing on our site is reviewed by US automotive fitment specialists before it goes live — so the compatibility data you read here is checked, not copied. We ship fast, support real customer questions with real answers, and stand behind the products we sell with a straightforward returns process. If you have a fitment question before you order, reach out — we would rather answer it now than process a return later. If your Tundra carries a 5.5-foot Fleetside bed and you are done letting weather, theft, and drag tax your workweek, this is the cover. Click Add to Cart now — the JiaYao Tri-Fold Tonneau Cover ships ready to install and built to last.