6FT Soft Roll-Up T Onneau Cover For T Oyota 16-22 T Oyota Tacoma Short Truck Bed--A86315-M44410S

Keep your cargo protected and your Tacoma looking sharp with the Mankee Soft Roll-Up Tonneau Cover — engineered specifically for the 2016-2022 Toyota Tacoma 6-foot short bed. Built for real-world conditions and designed to install in under 30 minutes without a single drill hole, this cover delivers professional-grade performance at a price that makes sense for working truck owners. COMPATIBILITY This Mankee tonneau cover is purpose-built for the 2016, 2017, 2018, 2019, 2020, 2021, and 2022 Toyota Tacoma equipped with the 6-foot (approximately 73.7-inch) short truck bed — the standard bed found on most Double Cab Tacoma configurations. It mounts directly to the factory OEM bed rails using a no-drill clamp-on system, preserving your truck's factory finish and keeping your warranty intact. Important fitment note: if you own a Tacoma Access Cab with the 5-foot short bed, this cover is not the correct fit — always measure your bed length from the inside of the bulkhead to the inside of the tailgate before ordering. The cover is compatible with factory rubber bed mats and drop-in liners. If you have an aftermarket spray-in bedliner, confirm that your rail width has not been significantly narrowed before purchasing, as thick spray coatings can occasionally affect clamp seating. BENEFITS • Instant cargo security — the low-profile soft cover conceals tools, camping gear, and valuables from prying eyes, deterring opportunistic theft far more effectively than an open bed ever could. • All-weather defense — heavy-duty UV-resistant vinyl sheds rain, sleet, snow, and road grime season after season, keeping your bed and its contents genuinely dry. • Full bed access in seconds — roll the cover toward the cab and lock it in place with the integrated hook-and-loop straps; no tools, no fumbling, no delay when you need to haul tall or oversized loads. • Aerodynamic fuel savings — the flat, streamlined profile reduces cab-end turbulence and drag compared to an open bed, contributing to measurable improvements in highway fuel economy over time. • Zero modification required — the clamp-on rail system leaves your bed rails completely undamaged, making this an ideal solution for leased trucks or owners who may want to remove the cover seasonally. • Sleek, low-profile appearance — the matte black finish integrates cleanly with the Tacoma's factory styling, giving your truck a purposeful, finished look without aftermarket aggression. TECHNICAL SPECS • Bed fit: 6 ft / 73.7-inch Toyota Tacoma short bed (2016-2022, 3rd Generation) • Cover style: Soft roll-up, single-panel design (tri-fold-free for maximum opening width) • Material: Heavy-duty marine-grade vinyl outer skin with reinforced internal support rods • Mounting system: No-drill clamp-on, mounts to factory OEM bed rails • Hardware finish: Corrosion-resistant coated aluminum and stainless steel hardware • Seal type: Foam perimeter weatherstripping on all four edges for a watertight seal • Roll retention: Integrated hook-and-loop cab-end straps hold the rolled cover securely while driving • Tailgate operation: Fully compatible with standard tailgate open/close; no tailgate removal required MATERIALS AND BUILD QUALITY The Mankee cover uses a heavy-duty marine-grade vinyl outer layer that has been treated for UV resistance, meaning it will not crack, fade, or delaminate after prolonged sun exposure the way cheaper covers do. The vinyl is stretched over a series of internal aluminum support rods that give the cover its rigid, flat profile when closed while still allowing smooth, effortless rolling when you need full bed access. The perimeter foam weatherstripping is die-cut to conform precisely to the Tacoma's bed rail geometry, creating a consistent seal around all four edges that resists water intrusion even during heavy downpours. The mounting clamps are constructed from corrosion-resistant aluminum with a protective coating, ensuring they will not rust or seize in wet climates or during winter road salt exposure. All stitching on the vinyl panels uses UV-stabilized thread to prevent premature degradation, and the hook-and-loop retention straps are rated for repeated daily cycling without loss of holding strength. INSTALLATION GUIDE Installing the Mankee tonneau cover on your 2016-2022 Tacoma requires no drilling, no special tools beyond a basic wrench or socket set, and typically takes 20-30 minutes for a first-time installer. Step 1: Open the tailgate and remove everything from the bed. Step 2: Unbox the cover and identify the front rail (marked), rear rail, side rails, mounting clamps, and hardware bag. Step 3: Place the front rail against the inside of the cab bulkhead, then position both side rails along the top of the truck's bed rails. Step 4: Slide the mounting clamps into the slots on the underside of the side rails, positioning one clamp near the front and one near the rear of each side rail. Step 5: Hand-tighten the clamp bolts until the rail assembly is held in position, then confirm the cover is centered and square before fully torquing the clamps to snug — do not overtighten, as this can distort the rail. Step 6: Feed the cover into the front rail channel and unroll it toward the tailgate. Step 7: Connect the rear edge of the cover to the tail seal and confirm all four weatherstrip edges are seated flush. Step 8: Close the tailgate, check the fit, and test the roll-and-lock function using the hook-and-loop cab straps. The entire process requires no permanent modifications. WHAT'S IN THE BOX • 1x Mankee soft roll-up vinyl tonneau cover panel • 2x Side mounting rails with integrated clamps • 1x Front header rail with channel • 1x Rear tail seal strip • 4x Mounting clamps with hardware • 2x Hook-and-loop retention straps • 1x Hardware and fastener bag • 1x Printed installation instruction sheet WHY SHOP WITH US When you order from our store, you get a team of US-based automotive specialists who understand the Tacoma platform and stand behind every product we carry. We vet each item for fitment accuracy before listing it, so you can order with confidence knowing the part is the right one for your specific truck. Our customer support team is available to assist with pre-sale fitment questions, installation guidance, and post-sale support. We process orders quickly, provide real tracking, and handle returns without the runaround. If there is ever a fitment issue, we make it right — because your Tacoma deserves parts that actually fit. Ready to protect your payload and upgrade your Tacoma's look? Add the Mankee Soft Roll-Up Tonneau Cover to your cart today and enjoy fast shipping, no-hassle returns, and the peace of mind that comes from buying the right cover for your 2016-2022 Toyota Tacoma 6-foot short bed.