Outdoor Mountain Bike Tailgate Mat And Pickup Truck Tailgate Protection Mat

Haul your mountain bikes to the trailhead without putting a scratch on your truck's finish. This heavy-duty 60-inch tailgate bike pad wraps your full-size pickup tailgate in multi-layer protective cushioning, keeping frames, forks, and handlebars from grinding paint, denting metal, or cutting through clearcoat — no matter how long the drive or how rough the road gets. Compatibility & Universal Fit This tailgate protection mat is engineered for universal compatibility with the most popular full-size pickups on the road in the United States today. It fits Ford F-150 (all cab configurations), Chevy Silverado 1500 and 2500, RAM 1500 and 2500, Toyota Tundra, GMC Sierra 1500 and 2500, Nissan Titan, and virtually any other standard-width full-size pickup tailgate. The adjustable strap-and-buckle system accommodates a range of tailgate heights and widths, so you get a snug, rattle-free installation without drilling a single hole or making any permanent modification to your truck. If you run a multi-vehicle fleet or regularly swap between a personal truck and a work rig, the fast-release buckles let you transfer this pad from vehicle to vehicle in under two minutes flat. Key Benefits • Shields tailgate paint, clearcoat, and bare metal from bike frames, handlebars, and fork dropouts throughout transport at any speed • Secures multiple bicycles with individual fork straps or frame loops, keeping each bike upright and separated so they cannot swing into one another at highway speed • Non-slip inner lining grips the tailgate surface positively so the pad stays locked in place over rough terrain, gravel roads, and sudden highway stops • No-drill, no-hardware installation preserves your factory finish and maintains full resale value on your truck • Fast-release buckles enable transfer between multiple trucks or fleet vehicles in under two minutes • Compact roll-up storage design lets the pad fit inside a truck cab, saddlebag, or small gear bin when not in use — no bulky rack to wrestle with Technical Specifications • Pad Width: approximately 60 inches — covers standard full-size truck tailgate widths • Pad Height: approximately 11–13 inches of coverage across the tailgate face • Foam Thickness: multi-layer padding with approximately 0.5–1 inch compressed protection depth • Bike Capacity: designed to carry multiple mountain bikes simultaneously with individual securing positions • Attachment System: adjustable strap-and-buckle with fast-release hardware; no tools required • Inner Surface: non-slip grip lining to prevent pad migration on tailgate surface • Outer Surface: weather-resistant outer shell rated for outdoor and highway use • Storage Format: roll-up design for compact storage; no rigid frame or bulky structure Materials & Build Quality The core of this tailgate pad is a multi-layer foam construction that combines shock-absorbing density foam with a durable outer shell designed to resist abrasion, UV exposure, and highway moisture. The inner facing is constructed from a non-slip textile lining that creates meaningful friction against powder-coated, painted, or bare metal tailgate surfaces, preventing the lateral creep that cheaper pads suffer from on long highway runs. Stitching throughout the pad uses reinforced thread at all high-stress points — particularly at the strap anchor zones — so the attachment system does not pull away from the body of the mat under load. The buckles are injection-molded from structural-grade polymer that resists brittleness in cold temperatures, which matters when you're loading bikes at dawn before a winter trail session. Every external surface is selected for washability; mud, trail dust, and chain grease wipe clean without degrading the material or compromising the grip lining over time. Installation Guide Installing this truck tailgate bike pad takes under five minutes and requires zero tools. Step one: lower your truck's tailgate to its open, horizontal position. Step two: center the pad horizontally across the tailgate face, making sure the non-slip lining faces down against the tailgate surface. Step three: route the top straps over the top edge of the tailgate and connect them to the rear-side anchor straps using the fast-release buckles. Step four: tighten each strap until the pad sits flush and immovable — give it a firm lateral tug to confirm there is no slide. Step five: load your bikes by resting the top tube or fork crown against the pad face and securing each bicycle using the individual fork straps or frame loops built into the pad face, spacing bikes evenly to distribute weight. On a new vehicle, it is worth test-driving one mile at low speed before heading to the highway to confirm strap tension has not shifted. To remove, simply release the buckles, pull the straps clear, and roll the pad for storage. What's in the Box • 1x 60-inch truck tailgate bike pad • Integrated adjustable strap-and-buckle attachment system • Individual bike securing straps or frame loops (built into pad) Why Shop With Expedite When you order from our store, you get a no-nonsense buying experience built around truck owners and outdoor enthusiasts who want the right part shipped fast. Every product listing goes through hands-on accuracy review so the fitment details you read match what arrives at your door. We back our products with straightforward return policies and responsive US-based customer support — no runaround, no overseas ticketing delays. Whether you're outfitting one personal truck or sourcing protection accessories for a commercial fleet, we make the process efficient and reliable from checkout to delivery. Protect your tailgate and ride your trails. Add this 60-inch mountain bike tailgate pad to your cart today and haul your bikes with zero worries about paint damage, dents, or clearcoat scratches — on any full-size pickup you own.