3-Fold 6FT Bed Tonneau Cover For Chevrolet 04-12 Colorado GMC 04-12 Canyon 290--A86315-2020401M32210YS

Stop leaving your gear exposed to the elements. The Mankee soft tri-fold tonneau cover is purpose-built for 2004-2012 Chevrolet Colorado and GMC Canyon owners who want professional-grade weather protection, fast bed access, and a factory-clean look — all without breaking the bank or spending a weekend in the driveway. Compatibility This cover is designed exclusively for first-generation 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, and 2012 Chevrolet Colorado and GMC Canyon pickups fitted with the standard 6-foot bed (approximately 72 inches measured from the inside of the bulkhead to the inside of the tailgate). If your inside measurement falls between 71 and 73 inches, this is the correct fit. This cover is NOT compatible with short beds, crew-cab short-bed configurations that deviate from 72 inches, or the second-generation Colorado and Canyon (2015 and newer). When in doubt, measure your bed before ordering — your truck will thank you. Key Benefits • All-Weather Cargo Protection: The heavy-duty marine-grade vinyl surface actively repels rain, sleet, UV rays, and highway road debris, keeping tools, groceries, camping gear, and job-site equipment dry and damage-free in all four seasons. • Three-Panel Folding System: Three rigid-backed panels fold forward toward the cab in seconds — no tools, no fumbling with snaps, no removing hardware. When work calls for a full, unobstructed 6-foot bed, you have it instantly. • No-Drill Clamp-On Installation: The clamping rail system attaches directly to your bed rail without drilling a single hole, preserving your truck's factory finish and resale value. • Aerodynamic Low-Profile Design: The flush, low-sitting profile reduces drag over an open bed, delivering modest but measurable fuel economy improvements on highway runs — a perk fleet operators and daily drivers both appreciate. • Concealed Cargo Security: When latched, the cover keeps your gear hidden from prying eyes, adding a practical layer of deterrence against opportunistic theft at job sites, trailheads, and parking lots. • Factory-Clean Appearance: Sleek matte-black styling integrates with the Colorado and Canyon's body lines for a look that's more showroom than aftermarket. Technical Specifications • Fitment: 2004-2012 Chevrolet Colorado / GMC Canyon — 6ft standard bed (72" / ~183 cm) • Cover Style: Soft tri-fold (3-panel folding) • Surface Material: Heavy-duty marine-grade vinyl, UV-stabilized • Frame / Cross Rails: Lightweight powder-coated aluminum • Mounting System: No-drill clamp-on; fits standard bed rails • Panel Count: 3 rigid-backed soft panels • Fold Direction: Front-to-rear folding toward cab • Hardware Finish: Corrosion-resistant black powder coat Materials and Build Quality The Mankee tri-fold cover is built around two complementary materials selected specifically for truck-bed duty. The outer surface uses a marine-grade, UV-stabilized vinyl compound — the same category of material used in boat covers and professional tarps — that resists cracking, fading, and brittleness across the full temperature range a working truck sees, from desert summers to northern winters. The seam stitching is reinforced at all fold points to prevent delamination or tearing after thousands of open-and-close cycles. Beneath the vinyl skin, each panel is stiffened by an internal structure that prevents pooling water from collapsing the cover inward. The mounting rails are extruded aluminum with a black powder-coat finish that won't rust even in high-humidity or road-salt environments. Every clamp, latch, and seal is designed to work together, creating a weather barrier that channels water away from the bed rather than letting it seep through panel gaps. Installation Guide Installing this cover requires no drilling, no special tools, and no professional installer — most owners complete the job in 20 to 30 minutes with basic hand tools. Step 1: Clean your Colorado or Canyon bed rails thoroughly with a damp rag to remove dirt and wax that could interfere with the clamp seal. Step 2: Lay the folded tonneau cover in the bed with the hinge side facing the cab. Step 3: Unfold the cover across the full bed length and align the aluminum side rails flush with the inside edge of your bed rails. Step 4: Slide the clamp brackets into position every 12 to 18 inches along each rail, ensuring equal spacing side to side. Step 5: Hand-tighten each clamp until snug, then go back around and tighten firmly with a socket or adjustable wrench — do not overtighten to the point of deforming the rail. Step 6: Attach the rear latch strap to your tailgate handle or anchor point per the included instructions. Step 7: Close the cover, check that all three panel seams lie flat, and verify the rear latch engages cleanly. Test the fold-forward action two or three times to confirm smooth operation. If any panel gaps appear uneven, loosen the nearest clamp, realign the rail, and re-tighten. What's in the Box • 3-panel soft tri-fold tonneau cover assembly (rails pre-attached) • Clamp-on mounting hardware set (aluminum rail clamps + hardware) • Rear latch and strap assembly • Weather-seal foam tape • Detailed installation instruction sheet Why Shop With Expedite We specialize in hard-to-find, vehicle-specific truck accessories for working owners who can't afford to wait or guess on fitment. Every listing in our catalog is verified against OEM bed dimensions so you receive a cover that fits right the first time. Our US-based support team can confirm compatibility for your specific Colorado or Canyon build before you complete your order — just reach out via chat or email. We stand behind every product with straightforward return and exchange policies because we know that trust, not just price, keeps customers coming back. Ready to protect your cargo and sharpen your truck's profile? Add the Mankee soft tri-fold tonneau cover to your cart today and enjoy same-week shipping to most US addresses.