Truck Universal Small Taillight American Version, Rubber Frame With Plug 10 LED Oval Light ,12V, 2 Red Glossy Covers,2 Transparent Glossy Covers -4-piece Set

When your rear lights fail on a busy delivery route or a late-night highway run, the consequences go beyond an inconvenient roadside stop — you risk DOT violations, fines, and most importantly, the safety of your crew and every driver behind you. These Universal Truck 10-LED Oval Taillights are built to end that risk with a rugged, plug-and-play solution engineered specifically for the North American commercial market. Compatibility is the foundation of this kit. These oval LED taillights are designed to fit the standard 4-inch oval marker lamp pocket found across an enormous range of commercial and medium-duty vehicles. Compatible platforms include Ford Econoline and Transit cargo vans, RAM ProMaster, Chevrolet Express, Freightliner M2 and Sprinter-based fleet builds, Kenworth and Peterbilt marker light positions, and trailer brands including Utility, Great Dane, and Wabash. They also drop into agricultural equipment and utility trailer applications that share the same standard oval cutout. Because fitment depends on your existing cutout dimensions, always measure your lamp pocket before ordering — if you run a standard North American 4-inch oval pocket, this set installs without modification. • Instant high-visibility illumination: 10 individual LEDs per lamp push far more usable light output than aging incandescent oval bulbs, cutting through rain, fog, and nighttime conditions so following drivers see you clearly at distance. • Dual-function cover system: Two red glossy covers serve as stop/tail and rear marker lamps while two transparent glossy covers work as backup, clearance, or auxiliary position lights — giving you flexible configuration across multiple vehicle positions. • Plug-and-play wiring: Factory-style connector plugs mean no splicing, no rewiring, and no special tools. Swap old bulbs for LED performance in minutes, not hours. • Rubber grommet frame: The vibration-dampening rubber housing absorbs road shock and engine vibration that cracks and loosens rigid plastic mounts over time, keeping your lights seated and sealed on rough delivery routes and highway miles alike. • 12V system ready: Designed natively for standard 12-volt DC truck, van, and trailer electrical systems with no ballast, no resistor pack, and no converter required. • DOT-style compliance design: Oval LED marker configurations in this format are the industry-standard spec for North American commercial vehicles, keeping your rig road-legal and audit-ready during fleet inspections. • Voltage: 12V DC • LEDs per lamp: 10 per unit (40 total across the 4-piece set) • Housing shape: Oval (standard 4-inch North American format) • Frame material: Rubber grommet, vibration-dampening • Lens/cover material: ABS plastic, high-gloss finish • Cover colors included: 2 red glossy, 2 transparent glossy • Wiring: Pre-wired plug connector, no splicing required • Operating environment: Designed for outdoor commercial vehicle use in rain, dust, and temperature variance The materials on these oval taillights are chosen for the punishment of daily commercial use. The lens covers are molded from high-gloss ABS plastic — a material known for its impact resistance, UV stability, and resistance to the road grime, cleaning chemicals, and temperature swings that destroy cheaper polystyrene lenses over a single season. The rubber grommet frame is a critical detail that separates professional-grade oval lights from budget substitutes. Rubber naturally flexes and returns to shape under vibration, preventing the fatigue cracking that rigid plastic snap-in mounts develop after months of highway driving. It also creates a weather-resistant seal between the light body and the lamp pocket, reducing moisture intrusion that corrodes bulb sockets and shorts wiring over time. Combined with the pre-terminated wiring plug, these components form a system built to outlast the incandescent fixtures they replace on a working commercial vehicle. Installation is straightforward for anyone with basic hand tools. Begin by parking the vehicle on a level surface and switching off the ignition to de-energize the electrical system. Locate the existing oval lamp pocket on your truck, van, or trailer panel. Remove the retaining ring or grommet holding the old light in place — a flathead screwdriver is typically sufficient. Pull the old lamp assembly forward and disconnect the wiring harness at the plug. Discard the old unit. Take your new LED oval light, connect the pre-wired plug to the vehicle harness — the connectors are keyed, so alignment is intuitive. Press the rubber grommet frame into the oval cutout until it seats flush with the panel surface. The grommet's lip should grip the panel edge evenly around the full perimeter. Restore power and test the lamp function before replacing any panels or trim. Repeat the process for all four positions. Total installation time for a full 4-piece replacement is typically 20 to 40 minutes depending on panel access. No soldering, no crimping, and no wiring diagrams required. • 4x 10-LED oval taillights (2 with red glossy covers, 2 with transparent glossy covers) • 4x rubber grommet frames (pre-installed on lamp bodies) • 4x pre-wired plug connectors (pre-installed) At Expedite, we stock commercial vehicle lighting that actually ships and actually fits — not vague universal listings that arrive undersized or without connectors. We vet our commercial lighting inventory against real North American vehicle applications, and our product descriptions reflect what installers and fleet managers need to make confident buying decisions: accurate dimensions, honest compatibility notes, and clear specifications. We back in-stock orders with fast dispatch and straightforward returns so your fleet doesn't sit idle waiting on a parts supplier that can't deliver. Ready to upgrade your truck, van, or trailer with reliable LED oval lighting that installs in under an hour? Add this 4-piece universal 10-LED oval taillight set to your cart today and get your rig back to full DOT compliance before your next run. Questions about fitment for a specific vehicle or trailer brand? Reach out to our team — we're here to help you get the right part the first time.