Soft Roll-Up Truck Bed Tonneau Cover, Compatible With 2017-2025 Ford F-250/350/450 Super Duty, Fits 6.8 Ft (6 Ft 10 In/82 In) Bed, Triple-Layer PVC Tonneau Cover With Three Aluminum Alloy Bars

Keep your cargo dry, your fuel bills lower, and your Super Duty looking sharp with the Vevor Soft Roll-Up Tonneau Cover — a no-compromise bed cover precision-matched to the 2017-2025 Ford F-250, F-350, and F-450 Super Duty long bed. Built from heavy-duty triple-layer crosslinked PVC and supported by three heavy-wall aluminum alloy bars, this cover delivers contractor-grade protection at a price that makes fleet sense. This tonneau cover is engineered exclusively for 2017, 2018, 2019, 2020, 2021, 2022, 2023, 2024, and 2025 model-year Ford F-250, F-350, and F-450 Super Duty trucks equipped with the 6.8 ft (6 feet 10 inches / 82 inches) long bed. It is not compatible with the 8 ft long-bed or any short-bed variant. To confirm fitment before ordering, close the tailgate and measure from the inside face of the bulkhead to the inside face of the tailgate. A measurement of approximately 82 inches means this cover is your correct fit. Always verify your actual bed length; an incorrect measurement leads to gaps, rattles, or a cover that simply will not mount. • Weatherproof cargo protection — the outer skin of the triple-layer PVC fabric is UV-treated and weather-sealed to shed rain, sleet, road spray, and sun exposure without cracking, fading, or delaminating over seasons of hard use. • Measurable MPG gains — the flat, aerodynamic low-profile silhouette reduces turbulent drag over the open bed at highway speeds, helping your heavy-duty Super Duty recoup real fuel savings on every interstate haul. • Full bed access in seconds — peel back the cover from the tailgate end and roll it toward the cab; three hook-and-loop straps lock the roll securely behind the cab, giving you complete, unobstructed access to the entire 82-inch bed. • Zero drilling required — adjustable aluminum alloy bed-rail clamps grip the rail without punching a single hole, preserving factory paint, resale value, and warranty coverage. • Secure locking at the tailgate — the integrated tail-end latch pairs with your factory tailgate lock so your gear is double-secured at every stop, whether you are parked at a job site or overnight at a rest area. • Easy solo installation — the clamp-on design means one person with basic hand tools can have this cover mounted and sealing in under 30 minutes, no lift required. • Cover Type: Soft roll-up, clamp-on no-drill mount • Compatible Vehicles: 2017-2025 Ford F-250, F-350, F-450 Super Duty • Bed Fit: 6.8 ft / 6 ft 10 in / 82 in long bed ONLY (does NOT fit 8 ft bed) • Outer Material: Triple-layer crosslinked PVC, 24 oz weight-rated marine-grade fabric • Frame: 3 heavy-wall aluminum alloy crossbars spanning the full bed width • Clamp Hardware: Adjustable aluminum alloy bed-rail clamps, no drilling required • UV Resistance: UV-stabilized outer layer rated for multi-season exposure • Closure: Hook-and-loop roll straps + integrated tailgate latch compatible with OEM lock The fabric at the heart of this cover is a 24 oz triple-layer crosslinked PVC composite — a construction borrowed from marine and commercial tarp applications, not from budget automotive accessories. The three distinct layers work together: the top-facing outer skin is UV-stabilized and surface-textured to repel water and resist abrasion from branches, tools rested on the cover, and highway grit. The intermediate bonding layer locks the outer and inner skins together under heat and pressure, eliminating the delamination that plagues single-layer or heat-sealed covers after a few winters. The inner facing is smooth and non-abrasive so it will not scratch bed liner coatings or the surfaces of soft-sided cargo bags resting against it. Stretched over three heavy-wall aluminum alloy support bars, the fabric maintains consistent tension across the full 82-inch span, preventing the pooling and sagging that collects standing water and eventually stresses seams. The aluminum bars resist corrosion in salt-belt states and flex minimally under snow load, keeping the cover taut season after season. Installing this Vevor tonneau cover on your Super Duty is a straightforward one-person job. Step 1: Remove any existing bed accessories from the rail area and clean the top rail surface with a dry cloth to ensure the clamps seat flush. Step 2: Lay the rolled cover assembly across the bed with the hinged frame running along the front (cab-side) rail. Step 3: Position the front crossbar flush against the back of the bulkhead and hand-tighten the two front clamps onto the bed rail — do not fully torque yet. Step 4: Unroll the cover toward the tailgate, keeping the fabric centered side-to-side, and position the second and third crossbars evenly spaced down the bed. Step 5: Clamp all remaining hardware onto both bed rails, confirming equal overhang on the driver and passenger sides. Step 6: Tighten all clamps to snug with a 10mm wrench or socket — firm contact is enough; over-torquing can mar the rail finish. Step 7: Close the tailgate, engage the integrated latch, and tug the cover fabric at the tail end to confirm tension and sealing. Total time for a first-time installer: approximately 20 to 30 minutes. No drilling, no modifications, no professional help needed. • (1) Vevor soft roll-up tonneau cover — triple-layer PVC fabric panel, pre-attached to front frame • (3) Heavy-wall aluminum alloy crossbars • (1) Set of adjustable aluminum alloy bed-rail clamps (driver and passenger pairs per bar) • (3) Hook-and-loop roll retention straps • (1) Integrated tailgate latch assembly • (1) Installation hardware pack (fasteners, rubber seals, corner end caps) • (1) Illustrated installation instruction sheet When you shop here, you get a single SKU that is in-stock, photographed from multiple angles, and priced transparently — no hidden freight fees, no bait-and-switch on fitment. Our product listings are built by US automotive specialists who verify compatibility data against OEM bed dimension charts, so the 82-inch fitment note you read here is not a guess copied from a Chinese supplier feed. We stand behind the accuracy of our fitment data and the quality of every unit we ship. Orders placed before cutoff ship same business day, and our US-based support team is reachable if you have a compatibility question before your order leaves the warehouse. At $182, the Vevor soft roll-up tonneau cover for your 2017-2025 Ford F-250, F-350, or F-450 Super Duty 6.8 ft bed is the smartest upgrade you can make to a working truck. Protect your tools, save on fuel, and lock your tailgate with confidence. Confirm your 82-inch bed length, add to cart, and get this cover delivered to your door — because your Super Duty hauls too much to leave the bed uncovered.