5 6 Bed Soft Lock & Roll Up Truck Bed For 2022-now T Oyota Tundra Tonneau Cover --A80034-12112

Keep your gear locked down and your Tundra looking sharp with the Mankee Soft Roll-Up Tonneau Cover — purpose-built for the 2022 and newer 3rd Generation Toyota Tundra. At a fraction of the cost of a hardcover, this premium lockable vinyl cover delivers real weather protection, fast full-bed access, and a clean factory-integrated appearance that upgrades your truck's entire profile. Compatibility This tonneau cover is engineered exclusively for the 2022, 2023, and 2024+ Toyota Tundra (3rd Generation) fitted with the 5.5 ft (approximately 66-inch) truck bed. Compatible cab configurations include the CrewMax and Double Cab, both of which are available with the 5.5 ft bed length. It does NOT fit the Tundra's 6.5 ft bed variant, and it is not compatible with 1st Generation (2000–2006) or 2nd Generation (2007–2021) Tundra models. Before purchasing, measure your bed interior from the bulkhead panel to the inside face of the closed tailgate. If you are unsure, check the door jamb sticker or your VIN for body configuration details. Getting the right fit ensures the side rails seat flush and the weatherstrip creates a watertight seal on all four sides. Key Benefits • Lockable Security — The integrated tailgate latch-and-lock system secures the cover at the rear of the bed, keeping cargo concealed from prying eyes during commutes, job sites, and overnight parking. No tools needed to lock or unlock. • Instant Full-Bed Access — Roll the cover forward toward the cab in seconds. Hook-and-loop retention straps hold it neatly in the rolled position so you can load full sheets of plywood, long lumber, or bulky equipment without removing any hardware. • All-Season Weather Resistance — A foam-backed rubber weatherstrip runs the entire perimeter, while tight-fitting extruded aluminum side rails channel water away through integrated drainage ports, keeping your bed dry in rain, snow, and dusty highway conditions. • Aerodynamic Profile — The low-profile roll-up design reduces wind drag compared to a bulky folding hardcover, contributing to better highway fuel economy and a sleeker appearance. • No-Drill Clamp Installation — Stainless-steel clamps bite onto the bed rail without drilling or permanent modification, preserving your truck's resale value and factory warranty. • One-Person Operation — Lightweight vinyl panels and the simple roll-up mechanism mean one person can open, close, and secure the cover without assistance in under 30 seconds. Technical Specifications • Bed Fit: 5.5 ft / 66 in Toyota Tundra (2022–present, 3rd Generation) • Cover Surface Material: Heavy-duty black vinyl with leatherette texture top finish • Frame Structure: Multi-section aluminum cross-bows providing rigid panel support under load • Rail Material: Extruded 6000-series aluminum side rails with integrated drainage channels • Seal System: Foam-backed EPDM rubber weatherstrip, full perimeter coverage • Mounting: No-drill stainless-steel bed-rail clamps, adjustable to factory bed dimensions • Operation: Manual roll-up with dual hook-and-loop retention straps for rolled position • Finish Color: Matte black — coordinates with factory Tundra trim on all color options Materials and Build Quality The Mankee tonneau cover is constructed around a dual-material philosophy: industrial-grade vinyl on the surface and aircraft-inspired aluminum underneath. The top skin uses a reinforced multi-layer vinyl laminate with a leatherette emboss that resists cracking, fading, and UV degradation through years of direct sun exposure. Unlike budget covers that use single-ply vinyl prone to sagging, the Mankee panel is tensioned across a series of powder-coated aluminum cross-bows that maintain a taut, drum-tight surface even in extreme temperature swings from desert summers to northern winters. The side rails are manufactured from extruded aluminum alloy, anodized for corrosion resistance, and feature machined drainage channels that route water out of the rail cavity and away from the bed floor. All fasteners are stainless steel to prevent rust bleed-through on your truck's paint. The tailgate seal bar uses the same foam-backed rubber compound as the perimeter strip, ensuring no gap is left unprotected at the most vulnerable point — the rear edge where rain and road spray enter most aggressively. Installation Guide Installing the Mankee soft roll-up tonneau cover requires no drilling and takes approximately 20 to 30 minutes with basic hand tools. Step 1: Unbox and lay out all components — side rails, cross-bow sections, tailgate seal bar, clamps, and the vinyl cover assembly. Step 2: Attach the front header rail across the bulkhead using the supplied stainless-steel clamps, ensuring it sits flush and level. Step 3: Snap the extruded aluminum side rails into the header rail end caps and run them along both bed rails toward the tailgate. Finger-tighten the clamps evenly. Step 4: Install the tailgate seal bar on the inside face of the tailgate using the adhesive-backed mounting strip — clean the tailgate surface with isopropyl alcohol first. Step 5: Lay the vinyl cover assembly over the cross-bows, aligning it symmetrically between the rails. Step 6: Torque all rail clamps to the specified setting (hand-tight plus a quarter turn is sufficient — avoid over-tightening on composite bed rails). Step 7: Confirm the latch engages cleanly with the tailgate seal bar and the cover lies flat without gaps along the weatherstrip. Step 8: Roll and unroll once to confirm smooth operation and adjust retention strap length as needed. No professional installation or lift required. What's in the Box • 1x Vinyl tonneau cover panel with aluminum cross-bow frame pre-assembled • 2x Extruded aluminum side rails • 1x Front header rail with end caps • 1x Tailgate seal bar • Stainless-steel bed-rail clamps (full set) • Hook-and-loop retention straps (pair) • Hardware bag with all fasteners • Illustrated installation manual Why Shop With Us We stock Mankee tonneau covers ready to ship fast, backed by responsive US-based customer support that actually knows the Toyota Tundra platform. Our listings include verified fitment data and real installation guidance — not machine-translated guesswork. If your cover arrives damaged or doesn't fit your confirmed bed size, our team resolves it quickly without the runaround. We stand behind every product we sell. Add the Mankee Soft Roll-Up Tonneau Cover to your cart today and give your 2022-2024 Toyota Tundra the cargo protection and clean profile it deserves — in stock and ready to ship.