Soft Roll-Up Truck Bed Tonneau Cover, Compatible With 2022-2025 Ford Maverick, Fits Styleside 4.5 Ft (4 Ft 6 In/54 In) Bed, Triple-Layer PVC Tonneau Cover With Three Aluminum Alloy Support Bars

The Vevor Soft Roll-Up Tonneau Cover is the purpose-built bed solution for Ford Maverick owners who want real weather protection, clean truck aesthetics, and total cargo flexibility — all without picking up a drill. COMPATIBILITY This tonneau cover is engineered exclusively for the 2022, 2023, 2024, and 2025 Ford Maverick equipped with the standard Styleside 4.5 ft bed (4 ft 6 in / 54 inches, measured bulkhead to tailgate). The no-drill clamp system is designed around the factory Ford Maverick bed rail profile. It is not compatible with box-delete configurations, over-rail spray-in bedliners that raise the rail height, or other truck models and trim levels. Before placing your order, measure your bed from the inside of the bulkhead to the inside of the closed tailgate and confirm you have exactly 54 inches. If you have the standard Styleside configuration, this cover ships ready to install straight out of the box. KEY BENEFITS • Instant Full Bed Access — The roll-up design lets you roll the cover forward and secure it directly behind the cab with the included straps in under 30 seconds. No hardware removal, no tools required — just open and go when you need to haul lumber, mulch, or oversized cargo. • Serious Weather Protection — Triple-layer PVC construction forms a taut, water-resistant seal across the entire bed opening, blocking rain, sleet, highway spray, and UV radiation from reaching your tools, groceries, or job-site gear on every drive. • Highway Fuel Efficiency — A sealed, low-profile cover measurably reduces aerodynamic drag compared to an open truck bed, contributing to improved MPG on highway miles — a real advantage for daily commuters and work-truck operators alike. • No-Drill Installation — The extruded aluminum side rails clamp directly onto the factory Ford Maverick bed rail lip. Zero permanent modifications means zero resale value impact and the ability to remove the cover in minutes if needed. • Low-Profile, Clean Look — The cover sits flush and tight against the bed rails, giving your Maverick a sleek, finished appearance without the bulk of a hard folding or retractable cover. • Tool-Free Tailgate Operation — The cover is fully compatible with the standard Maverick tailgate. Open and close the tailgate normally without adjusting or removing any part of the cover system. TECHNICAL SPECIFICATIONS • Vehicle Fit: 2022–2025 Ford Maverick, Styleside bed only • Bed Length: 4.5 ft / 4 ft 6 in / 54 inches (bulkhead to tailgate) • Cover Material: Triple-layer PVC vinyl with integrated UV inhibitors • Support Structure: Three (3) extruded aluminum alloy cross-support bars • Side Rail Material: Extruded aluminum with integrated no-drill clamps • Mounting Method: Clamp-on; fits factory bed rail lip — no drilling required • Water Resistance: Water-resistant triple-layer PVC barrier (not submersion-rated) • Weight Capacity: Light load support via aluminum cross bars (cover is not a load-bearing platform) MATERIALS & BUILD QUALITY The Vevor tonneau cover's surface is constructed from a triple-layer PVC vinyl composite that delivers a meaningfully different level of durability compared to single-ply alternatives common in the budget segment. The outer layer is formulated with UV inhibitors to resist surface cracking, fading, and brittleness caused by prolonged sun exposure — critical for Maverick owners in Sun Belt states like Texas, Arizona, and Florida. The inner layers add structural body so the cover maintains a taut, wrinkle-free profile in both summer heat and winter cold. The three aluminum alloy cross-support bars prevent the cover from sagging under moderate rain accumulation and maintain consistent tension across the PVC surface. The extruded aluminum side rails are precision-formed to match the Ford Maverick bed rail geometry, providing a secure, rattle-free clamp fit that does not rely on adhesive tape or foam padding alone. Every contact point between the rails and the truck bed is protected by a rubber seal strip that cushions the clamp and creates a secondary moisture barrier at the rail interface. INSTALLATION GUIDE Installing the Vevor roll-up tonneau cover on your Ford Maverick requires no special tools and typically takes 20 to 30 minutes. Step 1: Remove all items from your truck bed and clean the factory bed rail tops with a clean cloth to remove any debris or wax that could interfere with the clamp seal. Step 2: Lay out all components on a flat surface and identify the two aluminum side rails, three cross-support bars, the rolled PVC cover panel, and all clamp hardware. Step 3: Attach the cross-support bars to the PVC panel at the pre-sewn Velcro pockets — the front bar goes nearest the cab, the rear bar nearest the tailgate, and the third bar sits centered between them. Step 4: Position the assembled side rails along the top of the Maverick bed rails, aligning the front of each rail flush with the front of the bed opening at the bulkhead. Step 5: Tighten the integrated clamps underneath each side rail by hand first, then snug them down with a flathead screwdriver or the included tool to ensure firm, rattle-free contact without over-torquing the rail lip. Step 6: Lay the cover over the bars from front to back, feeding the rear edge over the tailgate seam. Step 7: Tension the side Velcro straps to pull the cover taut across all three bars. Step 8: Test the roll-up function — roll the cover from rear to front, secure the cab-end retention straps, and confirm the buckles hold under light wind load. Verify that the tailgate opens and closes freely with the cover in both positions. WHAT'S IN THE BOX • 1× Triple-layer PVC roll-up cover panel (pre-attached to front rail section) • 2× Extruded aluminum side rails with integrated no-drill clamps • 3× Aluminum alloy cross-support bars • Clamp hardware kit (bolts, rubber seal strips, fasteners) • Cab-end retention straps with buckles • Installation instruction sheet WHY SHOP WITH US We specialize in hard-to-find fitment-specific truck accessories for compact pickups, work trucks, and commercial vehicles. Every listing on our store is verified against OEM bed dimensions before it goes live — so when we say this cover fits the 2022–2025 Ford Maverick Styleside 4.5 ft bed, we mean it with confidence. Our team responds to fitment questions fast, and we stand behind every order with a clear return policy. The Vevor brand is recognized in the US commercial and automotive accessory market for delivering durable, properly engineered products at a price point that makes sense for working truck owners. Order the Vevor Soft Roll-Up Tonneau Cover for your 2022–2025 Ford Maverick today. Protect your cargo, sharpen your truck's look, and keep every haul ready for whatever the day demands — add to cart now.